Roseville Repipe
Skip to main content

Roseville Repipe: PEX Repiping in Roseville, CA

Roseville Repipe does PEX repiping in Roseville, CA. We take out old galvanized, copper, or polybutylene water lines and run new PEX to every fixture. You get new shutoff valves, a pressure-tested system, and patched walls when we're done.

Monday to Saturday, 7:00 AM to 7:00 PM

Get a Free Repipe Quote

By submitting, you agree to our Privacy Policy and Terms of Service.

What is PEX pipe?

PEX is cross-linked polyethylene. It's a flexible plastic tubing made for water supply lines. It comes in long coils, so one piece can run from the water heater to a far bathroom with no joints in the middle. Hot lines are often red and cold lines blue, but the color doesn't change the pipe.

California added PEX to the state plumbing code in 2009. A court challenge knocked that approval back for a while, and the state approved it again with an effective date of August 18, 2010. Today PEX is used on new homes and repipes all over the Roseville area.

What's the difference between PEX-A and PEX-B?

They're made two different ways, and they get joined with different fittings.

PEX-A vs. PEX-B
PEX-APEX-B
How it's madeEngel methodSilane method
FlexibilityVery flexible, bends tightStiffer
KinksA kink can often be fixed with heatA kink usually means cutting it out
FittingsExpansion fittings with a sleeveCrimp or clamp rings
CostCosts moreCosts less

Both work for a repipe. PEX-A expansion fittings keep the inside opening of the joint wide, which helps flow. PEX-B costs less up front. We'll talk through which one makes sense for your house.

Why do most Roseville repipes use PEX?

Because it gets the job done with fewer holes in your walls. PEX bends around corners and snakes through attics and walls in long runs. Fewer fittings means fewer places to leak and fewer spots where we have to open the drywall.

Here's what PEX does well:

  • Costs less to install than copper
  • Needs fewer and smaller wall openings
  • Has fewer joints behind the walls
  • Doesn't rust or build up scale inside like galvanized steel
  • Handles freezing better than rigid pipe because it can stretch a little
  • Goes in faster, so the house is back to normal sooner

PEX has limits too. It can't sit in sunlight, so it stays inside walls, attics, and crawlspaces. It shouldn't run right next to a water heater flue or other hot spots. And it needs to be supported the right way so it doesn't sag.

Should you use a manifold or trunk and branch?

There are two common ways to lay out a PEX system:

  • Manifold system: a central block near the water heater or main line with a separate line to each fixture. Each line gets its own shutoff, so you can turn off one sink without shutting down the house.
  • Trunk and branch: one larger main line runs through the house, with smaller lines branching off to each fixture. It uses less pipe.

A manifold uses more pipe but makes future repairs simple. Trunk and branch is closer to how most older homes were plumbed. We pick the layout based on the house, the number of fixtures, and where the water heater sits.

How does a PEX repipe go in a Roseville home?

Most homes around here are one or two stories, many on a slab. In a slab home, we run the new lines through the attic and drop them down inside the walls to each fixture. In a crawlspace home, we often run the lines under the floor instead.

  1. We protect floors and furniture.
  2. We make small access cuts in the drywall where lines need to drop.
  3. We run the new PEX and hook up each fixture with new shutoff valves.
  4. We tie into the main line and the water heater.
  5. We pressure test the whole system.
  6. The inspector signs off, and we patch the walls.

Some cities, like Lincoln, also have the plumber sign a PEX form saying the new system was flushed the way the California Plumbing Code says. We handle that paperwork with the permit.

What does a PEX repipe cost?

It comes down to the size of the house, the number of bathrooms, one story or two, attic access, and how much drywall needs patching. PEX usually costs less than copper for the same house. Read our Roseville repipe cost guide for the details.

Comparing materials? See copper repiping or read PEX vs. copper. If only part of the house needs work, a partial repipe may be enough.

PEX repiping FAQs

Is PEX allowed in California?

Yes. PEX is part of the California Plumbing Code for water supply lines, and it's used on repipes all over the Roseville area.

How long does PEX last?

PEX has been used in homes for decades. How long it lasts depends on installation, water conditions, and keeping it out of sunlight and away from high heat.

Can mice or rats chew PEX?

They can chew plastic, including PEX. If you've had rodents in the attic, tell us so we can plan the route and you can deal with the rodents too.

Is PEX noisy?

PEX is often quieter than copper because it flexes a little and doesn't bang as much when a valve shuts. Good support straps matter too.

Can you connect PEX to my existing copper?

Yes. On a partial repipe, we use the right transition fittings to tie PEX into the copper that stays.

Do you use PEX-A or PEX-B?

We install both. PEX-A costs more and uses expansion fittings. PEX-B costs less and uses crimp or clamp rings. We'll go over the choice with your quote.

Related services

Areas we serve

Ready for new PEX lines?

Call or send a few details about your house. We'll give you a price for a PEX repipe.

Get a Free Repipe Quote

By submitting, you agree to our Privacy Policy and Terms of Service.

Call NowFree Quote