Roseville Repipe
Skip to main content

How Much Does a Whole House Repipe Cost in Roseville, CA?

A whole house repipe is one of the bigger checks you'll write for a house. The price isn't a mystery, though. A handful of things set it, and once you know them, you can tell pretty quick whether a quote makes sense.

Last updated: November 18, 2026

Monday to Saturday, 7:00 AM to 7:00 PM

Get a Free Repipe Quote

By submitting, you agree to our Privacy Policy and Terms of Service.

What does a whole house repipe cost on average?

National cost guides are a good starting point.

Angi's 2026 cost data puts the average U.S. repipe at about $7,500, with a normal range of $1,500 to $15,000.

Source: Angi: How Much Does It Cost to Repipe a House?

That range is wide for a reason. The low end is a small partial repipe. The high end is a big house with a lot of bathrooms, two stories, or copper pipe. These are national numbers, not our prices. Your price depends on your house.

What sets the price of a repipe?

These are the biggest things, in about the order they matter:

  1. Number of fixtures and bathrooms. Every sink, toilet, tub, shower, washer, and hose bib needs its own line and shutoff. More bathrooms means more pipe and more connections.
  2. Number of stories. Getting lines to a second floor takes more work than a single-story house.
  3. Slab or crawlspace. Slab homes usually get lines run through the attic. Crawlspace homes often get lines run under the floor.
  4. Attic access. A roomy attic is fast to work in. A tight attic with low roof pitch takes longer.
  5. Pipe material. Copper costs more than PEX for both the pipe and the labor.
  6. Drywall. More openings means more patching and texture work.
  7. The main water line. Replacing the line from the meter to the house adds to the job.
  8. Extras. A new pressure regulator, new hose bibs, or moving fixtures add cost.

How much more does copper cost than PEX?

Copper costs more in two ways. The pipe itself costs more, and it takes more time to install, because every turn needs a fitting and every joint gets soldered or pressed. PEX bends around corners in long runs, so it needs fewer fittings and usually fewer wall openings.

That's why most repipes around here use PEX. If you want copper, expect the price to go up. Our PEX vs. copper guide goes through the tradeoffs.

What local rules can add to the cost in Roseville?

A couple of things are specific to Roseville and the towns around it:

  • Permit fees. Every repipe gets a permit and an inspection. Fees are set by each city, town, or county, so they're different in Roseville, Rocklin, Granite Bay, and the rest.
  • Water conserving fixtures. For homes built before January 1, 1994, the City of Roseville's handout on the state water conservation law says water conserving plumbing fixtures must be installed throughout the home as a condition of building permits. If your older home still has high-flow toilets or showerheads, plan for that.
  • Smoke and carbon monoxide alarms. Some local permits for this kind of work call for smoke and carbon monoxide alarms. Loomis, for example, includes an alarm declaration in its plumbing permit submittals.

None of those are a reason to skip the permit. They're just things to know up front so the price is right the first time. See our Roseville repipe permits guide.

Is a partial repipe cheaper?

For the job itself, yes. A partial repipe of one bathroom or one line costs less than the whole house. But a lot of the cost of any repipe is setup, permits, wall openings, and patching. If the rest of the pipe is the same age and starts leaking a few years later, doing it in pieces can cost more in the end.

We'll give you both prices when it makes sense, so you can decide.

What about drywall and cleanup?

Drywall patching is part of almost every repipe. How much depends on the number of openings, ceilings, and the wall texture. Some companies leave the holes for you to deal with. Ask before you sign. We include drywall repair after repipe in the conversation from the start.

How do you get an accurate repipe quote?

A firm price takes a walk-through. To get a useful ballpark first, have this ready:

  • The number of bathrooms and the number of stories
  • About when the house was built
  • What pipe you have now, if you know (a photo of the pipe at your water heater helps)
  • Slab or crawlspace
  • Any leaks you've had and where
  • Whether you want PEX or copper
  • Whether you've had trouble with the line from the meter to the house

You can send all of that with the form on this page. For our main service, see whole house repipe in Roseville. To see the material we use most, see PEX repiping.

Repipe cost FAQs

Why do repipe quotes vary so much?

Some quotes include drywall, the permit, and the main line, and some don't. Compare what's included, not just the total.

Is it cheaper to fix leaks one at a time?

Each repair is cheaper than a repipe. But if leaks keep coming, the repairs add up, and each leak can mean water damage too.

Does homeowners insurance pay for a repipe?

Usually not for the pipe itself. Some policies cover water damage from a sudden leak. Call your agent.

Does the permit cost extra?

The permit fee is part of the job. Each city, town, or county sets its own fees.

Is PEX always cheaper than copper?

For the same house, PEX almost always costs less to install, because the pipe costs less and it needs fewer fittings.

Can you give me a price without coming out?

We can give you a rough range over the phone. A firm price takes a walk-through, because attic access and fixture count change the job a lot.

Want a real number for your house?

Call or send a few details. We'll set up a walk-through and give you a written price.

Get a Free Repipe Quote

By submitting, you agree to our Privacy Policy and Terms of Service.

Call NowFree Quote