Roseville Repipe
Skip to main content

Slab Leak Signs and Repair Options: Reroute vs. Direct Repair

A slab leak is a leak in a water line under or inside the concrete floor of your house. You can't see it, but there are signs. Here's how to spot one, how it gets found, and how the two main fixes compare.

Last updated: November 18, 2026

Monday to Saturday, 7:00 AM to 7:00 PM

Get a Free Repipe Quote

By submitting, you agree to our Privacy Policy and Terms of Service.

What are the signs of a slab leak?

  • A warm or hot spot on the floor
  • The sound of water running when everything is off
  • A water bill that jumps with no change in use
  • The water meter moving when no water is on
  • Damp carpet, a wet pad, or cupping wood floors
  • Mildew or a musty smell near the floor
  • New cracks in floors or walls
  • A water heater that seems to run all the time

A warm spot usually means a leak on a hot line. Hot lines leak more often than cold lines, because heat and the swing from hot to cool put more wear on the pipe. A cold line leak won't feel warm, so watch the bill and the meter too.

How can you check for a slab leak yourself?

The water meter test is the easiest place to start.

  1. Turn off every faucet, appliance, and sprinkler.
  2. Find your water meter, usually in a box near the street or sidewalk.
  3. Watch the leak indicator or the sweep hand for a few minutes.
  4. If it moves, water is going somewhere.
  5. Shut the main valve at the house. If the meter stops, the leak is likely inside the house. If it keeps moving, the leak may be in the yard line.

A moving meter doesn't prove you have a slab leak. A running toilet or a dripping hose bib can do it too. Check those first. If they're fine and the meter still moves, it's time to call.

How do slab leaks get found?

A good leak search narrows it down step by step before anyone breaks concrete:

  • Isolate the hot and cold sides to see which one is losing pressure
  • Listen for the leak with acoustic gear on the floor
  • Look for warm spots with a thermal camera on hot line leaks
  • Trace where lines run under the slab so you know which pipe you're hearing
  • Check moisture in baseboards, walls, and flooring

Knowing which line is leaking matters as much as knowing where. It decides the fix. See leak detection.

What are the options for fixing a slab leak?

There are two main ways:

Slab leak repair options
 RerouteDirect repair
How it worksAbandon the leaking line and run a new one through the attic or wallsBreak open the floor at the leak and fix that section of pipe
Slab damageNoneA hole in the concrete
FlooringStays putThe flooring over the leak has to come up and be replaced
Wall openingsSmall access cuts where the new line dropsUsually none
Best forOlder pipe, long runs, repeat leaks, nice floorsNewer pipe and one leak in an easy spot
Future leaks on that lineThe old line is out of serviceThe rest of the old line is still under the slab

When is a reroute the better choice?

Most of the time, for older homes. If one spot under the slab leaked, the rest of that line is the same age and has seen the same wear. Fixing one spot leaves the rest down there.

A reroute moves that line up into the attic and walls, where it's easy to reach if anything ever happens again. It also skips breaking tile, wood, or stone floors, which can cost more to replace than the plumbing repair itself. Most reroutes use PEX because it bends through the attic and down the walls. See slab leak repair.

When does a direct repair make sense?

A direct repair can be the right call when:

  • The pipe is fairly new and the leak looks like a one-off, like damage from a nail or a bad fitting
  • The leak is in an easy spot with cheap flooring on top
  • A reroute would be very long or hard in that house

We'll show you both options for your house and tell you which one we'd pick.

When does a slab leak mean you need a repipe?

When it keeps happening. One slab leak can be bad luck. Two or three in a few years usually means the pipe under the house is wearing out. At that point, a partial repipe of the slab lines or a whole house repipe saves you from chasing leaks one at a time.

What about insurance and water damage?

Coverage depends on your policy. Some policies cover water damage and the cost to get to the leak, but not fixing the pipe itself. Call your agent before work starts, take photos of any damage, and keep your paperwork.

If the leak ran for a while, wet drywall, carpet pad, and insulation may need to dry out or come out. Things that stay wet can grow mold.

Slab leak FAQs

How common are slab leaks?

They're common in slab homes with older copper lines under or in the concrete. Hot lines leak more often than cold lines.

Can a slab leak damage my foundation?

Water running under a slab for a long time can wash out or soften soil under the concrete. That's one reason not to wait.

Is a reroute more expensive than a direct repair?

Not always. A direct repair also means concrete and flooring work. A reroute can cost less once floors are counted.

How long does a slab leak repair take?

Many reroutes are done in a day. A direct repair can take longer because of concrete and flooring.

What should I do right now if I think I have a slab leak?

If water is coming up through the floor, shut off the main valve at the house. Then call for leak detection.

Can slab leaks happen in newer homes?

Yes. Newer homes can get slab leaks from a bad fitting, a nail, or pipe that rubs against concrete.

Think you have a slab leak?

Call us. We'll find it and lay out your options before anything gets torn up.

Get a Free Repipe Quote

By submitting, you agree to our Privacy Policy and Terms of Service.

Call NowFree Quote