Roseville Repipe
Skip to main content

Roseville Repipe: Whole House Repipe and Slab Leak Repair in Roseville, CA

Roseville Repipe does whole house repipes in Roseville, CA. We pull out old galvanized, copper, and polybutylene water lines and put in new PEX repiping or copper. We also handle slab leak repair, leak detection, and water line work. When the pipe is in, we patch the walls and get the permit signed off.

Monday to Saturday, 7:00 AM to 7:00 PM

Get a Free Repipe Quote

By submitting, you agree to our Privacy Policy and Terms of Service.

What is a whole house repipe?

A whole house repipe means we replace every water supply line in the house. That's the hot and cold lines that run from the main shutoff to each sink, tub, shower, toilet, washer, water heater, and hose bib. We put in new lines, new stub-outs, and new shutoff valves at every fixture.

A repipe does not touch your drain lines. Drains and sewer pipes are a different system. A repipe is about the pressurized water that comes into the house and goes to your faucets.

Here's how a normal repipe job goes:

  1. We walk the house, find the main shutoff, and look at the old pipe where we can see it.
  2. We count fixtures, check water pressure, and look at the attic, crawlspace, or slab to plan the route.
  3. We give you a written price and pull the permit.
  4. We cover floors and furniture, then make small cuts in the drywall only where we need access.
  5. We run the new lines, hook up each fixture, and pressure test the whole system.
  6. The city inspector checks the work. Then we patch the drywall.

Why do Roseville homes need a repipe?

Age is the big one. Roseville grew up around the railroad, and its oldest homes sit near downtown and the older neighborhoods around it. A lot of the rest of the city was built from the 1970s on.

Census survey estimates for the Roseville City School District area put about 13% of homes before 1970, about 37% between 1970 and 1999, and about half in 2000 or later.

Source: U.S. Census ACS data for the Roseville City School District area, via NCES

So the reasons people call us depend on when the house was built:

  • Older homes near downtown can still have galvanized steel pipe that rusts from the inside and chokes down the flow.
  • Homes from the late 1970s into the mid 1990s were built during the years polybutylene pipe was sold. That gray plastic pipe is known for cracking and failing.
  • Copper homes of any age can get pinhole leaks, and once a few show up, more tend to follow.
  • Newer homes usually call us for a slab leak, a leak in a wall, or a main water line problem, not a full repipe.

Not sure what you have? Look at the pipe going into your water heater or under a sink. Gray steel with threaded joints is galvanized. Shiny or dull orange metal is copper. Gray plastic is often polybutylene. Red, blue, or white plastic tubing is usually PEX.

What is Roseville water like on pipes?

Roseville's tap water comes from more than one source, and that changes what's in it from season to season.

Roseville Environmental Utilities' 2025 Water Quality Report says the city used both groundwater and surface water in 2025. Folsom Lake surface water averaged 26 parts per million of hardness. Groundwater averaged 95 parts per million, with readings from 31 to 280. The city can also get up to 10 million gallons a day of treated water from the Placer County Water Agency. The report says pH is adjusted at the treatment plant to reduce corrosion.

Source: City of Roseville Water Quality Reports

Folsom Lake water is soft. Groundwater is harder, and the range is wide. Hard water leaves scale in water heaters and fixtures. Soft water doesn't leave much scale at all. Pipes fail for a lot of reasons, though: age, the pipe material, water pressure, how the pipe was installed, and the water itself. When we look at your house, we look at the pipe, not just the water report.

Some parts of east Roseville get water from the San Juan Water District instead of the city. Your water bill tells you who your supplier is.

What pipe do we put in?

Most of our repipes use PEX. Some homeowners want copper, and we do that too. Here's how they compare:

Repipe materials we install
PipeWhat it isGood to know
PEX-AFlexible plastic tubing made by the Engel method, joined with expansion fittingsThe most flexible PEX. Expansion fittings keep the inside opening wide.
PEX-BPEX made by a different process, usually joined with crimp or clamp ringsStiffer than PEX-A and costs a little less.
Copper Type LCopper pipe with a thicker wallLasts a long time and costs more.
Copper Type MCopper pipe with a thinner wallLighter and cheaper than Type L.

PEX bends around corners, so it needs fewer fittings and smaller wall openings. That's a big reason it costs less than copper to install. Many PEX jobs also use a manifold, which is a central block near the water heater with a shutoff for each line. Read our PEX vs. copper guide for the long version.

What services does Roseville Repipe offer?

We do repipes and leak work. We don't unclog drains or install toilets. Our work is the water lines.

How much does a whole house repipe cost in Roseville?

It depends on the house. These are the things that move the price the most:

  • How many bathrooms and fixtures the house has
  • One story or two stories
  • Slab, crawlspace, or a mix
  • How easy the attic is to work in
  • PEX or copper
  • Whether the main water line from the meter gets replaced too
  • How much drywall needs patching

For a national picture, Angi's 2026 cost data puts the average repipe at about $7,500, with most jobs between $1,500 and $15,000. Those are national numbers, not our prices. A bigger house, a two-story layout, or copper pipe pushes it higher. Our Roseville repipe cost guide walks through it in more detail.

How long does a repipe take, and can you stay home?

Most single-family homes take one to three days of work. A small one-story house with good attic access goes faster. A big two-story house with a lot of bathrooms takes longer.

Yes, you can stay home. Your water gets shut off while we tie in the new lines, so plan on some hours without water. We cover floors and furniture, keep the cuts small, and clean up each day. After the inspection, we patch the walls. See what happens during a repipe for the day-by-day version.

Do you need a permit to repipe a house in Roseville?

Yes. The City of Roseville says a building permit is needed for projects as small as a water heater replacement. A repipe changes the water piping in the whole house, so it gets a permit and an inspection. The city's quick, over-the-counter permit list covers jobs like water heaters and sewer lines, not repipes.

There's one more Roseville rule to know. For homes built before January 1, 1994, the city's handout on the state water conservation law says water conserving plumbing fixtures must be installed throughout the home as a condition of building permits. Read more in our Roseville repipe permits guide.

Do you fix slab leaks and other leaks too?

Yes. Plenty of our calls aren't full repipes. A hot spot on the floor, a water bill that jumped, or the sound of water running when everything is off can all point to a hidden leak.

We find it first with leak detection. If the leak is under the concrete, we fix it with slab leak repair, either by opening the floor and fixing that spot or by running a new line over the top through the attic or walls. If the problem is the line from the meter to the house, that's water line replacement and repair.

Where does Roseville Repipe work?

We work all over Roseville and the towns around it:

Not sure if we come out your way? See all of our service areas or just call and ask.

Repipe guides for Roseville homeowners

Whole house repipe FAQs

How do I know if I need a whole house repipe?

More than one leak in a year, rusty or brown water, low pressure at more than one fixture, or gray plastic polybutylene pipe are the common signs. If you've had one pinhole leak in copper, it's worth having the rest of the pipe looked at.

Do you have to tear out all my walls?

No. We make small access cuts where the lines run and where they connect to fixtures. Most of the pipe goes through the attic or crawlspace. We patch the cuts when the work is done.

Is PEX or copper better for a repipe?

Both are approved in California and both work. PEX costs less, bends around corners, and needs fewer wall openings. Copper costs more and some people just prefer metal pipe.

Will I have water during the repipe?

For most of each day, no, while we're tying in lines. We plan the shutoffs and tell you ahead of time so you're not caught off guard.

Does a repipe include the water heater?

We reconnect your water heater to the new lines. Replacing the water heater itself is a separate job, and it needs its own permit in Roseville.

Do you replace the drain lines too?

No. A repipe is the water supply lines. Drains and sewer lines are a different system.

Tired of leaks and low pressure?

Call or send a few details about your house. We'll tell you what it needs and what it costs.

Get a Free Repipe Quote

By submitting, you agree to our Privacy Policy and Terms of Service.

Call NowFree Quote