Roseville Repipe
Skip to main content

Roseville Repipe: Copper Repiping in Roseville, CA

Roseville Repipe does copper repiping in Roseville, CA for homeowners who want metal water lines. We replace old galvanized pipe, failing copper, or polybutylene with new Type L or Type M copper, put in new shutoff valves, and pressure test it all before the walls close up.

Monday to Saturday, 7:00 AM to 7:00 PM

Get a Free Repipe Quote

By submitting, you agree to our Privacy Policy and Terms of Service.

What is a copper repipe?

A copper repipe replaces the water supply lines in your house with new copper pipe. It's the same job as a PEX repipe, just with a different material. We run new hot and cold lines from the main shutoff to each fixture and the water heater.

Copper is rigid, so it goes in as straight runs joined with fittings at each turn. The joints are either soldered with a torch or joined with press fittings using a press tool.

What's the difference between Type L and Type M copper?

Copper pipe comes in different wall thicknesses. The thicker the wall, the more copper, and the more it costs.

Copper pipe types
TypeWallWhere it's used
Type KThickestMostly underground water service lines
Type LThickerInside lines where you want more wall, and some underground use
Type MThinnerInside lines where code allows it

The color printed on the pipe tells you the type. Type L is marked in blue and Type M in red. For a house repipe, we'll go over which type fits your budget and what your local inspector expects.

Why do some homeowners pick copper over PEX?

Copper costs more, so most of our repipes are PEX. But some people want copper, and they have good reasons:

  • It's metal, so rodents can't chew through it
  • It can handle sunlight and heat better than plastic
  • It's been used in homes for a very long time
  • Some buyers and homeowners just like seeing copper
  • It holds its shape, so long exposed runs look neat

The tradeoffs are real too. Copper costs more for the pipe and more for the labor. Every turn needs a fitting, and that can mean more or bigger wall openings. And copper can get pinhole leaks over time.

Why does copper get pinhole leaks?

Pinhole leaks are small holes that eat through the pipe wall from the inside or outside. There's no single cause. Water chemistry, how fast the water moves through the pipe, sediment, how the pipe was installed, and stray electrical current can all play a part.

Roseville's water report is a good place to start if you're curious about your water. The city blends Folsom Lake water and groundwater, and the hardness of each is very different. The report also says pH is adjusted at the treatment plant to reduce corrosion. We don't blame any one thing for a pinhole leak without looking at the pipe.

What we do know is this: once a copper system starts getting pinhole leaks, more usually follow. One leak can be patched. When there's a second and a third, it's time to talk about a repipe.

How does a copper repipe go?

It goes the same way as any repipe, with a little more cutting to get fittings in place.

  1. We protect floors and furniture.
  2. We open the walls where the new lines will run and turn.
  3. We run the new copper and join it at each fitting.
  4. We install new shutoff valves at each fixture.
  5. We tie into the main line and the water heater.
  6. We pressure test it, get the inspection, and patch the drywall.

If any galvanized pipe stays in the house, we use a dielectric fitting where copper meets steel. Two different metals touching can corrode where they join.

What does a copper repipe cost?

Copper usually costs more than PEX for the same house, because the pipe costs more and every joint takes more time. The size of the house, the number of bathrooms, and how many stories you have still matter the most. See our Roseville repipe cost guide.

Want to compare? Read PEX repiping and our PEX vs. copper guide. If you have a leak under the floor, see slab leak repair.

Copper repiping FAQs

Is copper better than PEX?

Neither one is better for every house. Copper is metal, holds up to heat, and costs more. PEX is flexible, costs less, and needs fewer wall openings.

Should I use Type L or Type M copper?

Type L has a thicker wall and costs more. Type M is thinner and costs less. We'll go over the choice and what the local inspector expects.

Will new copper get pinhole leaks too?

It can over time. New pipe installed right is a fresh start, but no material lasts forever. Water conditions and installation both matter.

Do you use solder or press fittings?

Both. Soldered joints are the traditional way. Press fittings join copper with a press tool and no open flame, which can help in tight spots.

Can you mix copper and PEX?

Yes. Some homeowners want copper where the pipe shows, like under sinks, and PEX inside the walls. We use the right transition fittings.

Does copper take longer to install?

Usually, yes. Each turn needs a fitting and each fitting takes time. Ask about the schedule when you get your quote.

Related services

Areas we serve

Want copper lines in your home?

Call or send a few details. We'll give you a price for a copper repipe.

Get a Free Repipe Quote

By submitting, you agree to our Privacy Policy and Terms of Service.

Call NowFree Quote