PEX vs. Copper: Which Pipe Is Better for a Repipe?
If you're getting a repipe, the first real choice is the pipe. Almost every repipe around Roseville uses PEX or copper. Both work. They just cost different amounts, go in differently, and hold up to different things.
Last updated: November 18, 2026
Monday to Saturday, 7:00 AM to 7:00 PM
What's the difference between PEX and copper?
PEX is a flexible plastic tubing called cross-linked polyethylene. Copper is rigid metal pipe. Here's how they stack up for a house repipe:
| PEX | Copper | |
|---|---|---|
| What it is | Flexible plastic tubing | Rigid metal pipe |
| Cost to install | Lower | Higher |
| Fittings | Fewer, because it bends | One at every turn |
| Wall openings | Usually fewer and smaller | Usually more |
| Sunlight | Can't be left in sunlight | Holds up fine |
| Rodents | Can be chewed | Can't be chewed |
| Freezing | Can stretch a little | Rigid, can split |
| Noise | Often quieter | Can bang when valves shut |
Is PEX allowed in California?
Yes. California was one of the last states to add PEX to its statewide plumbing code.
CONTRACTOR magazine reported that the California Building Standards Commission approved PEX for the state plumbing code in January 2009, and it became part of the code in August 2009. After a court challenge, the commission approved it again, with an effective date of August 18, 2010, for the 2007 California Plumbing Code and January 1, 2011, for the 2010 code.
Source: CONTRACTOR magazine on PEX in the California Plumbing Code
Today the 2025 California Plumbing Code is in effect. The state's Building Standards Commission says the 2025 California Building Standards Code took effect on January 1, 2026. Some cities around here have their own PEX paperwork. The City of Lincoln, for example, has a PEX certification form the plumbing contractor signs at final inspection, saying the new lines were flushed per Section 604.1.2 of the code.
What's the difference between PEX-A and PEX-B?
They're both PEX. They're made two different ways and joined with different fittings.
- PEX-A is made by the Engel method. It's the most flexible. It's joined with expansion fittings, where the tubing is stretched over the fitting and shrinks back tight. A kink can often be fixed with heat. It costs more.
- PEX-B is made by the silane method. It's stiffer. It's usually joined with crimp or clamp rings. It costs less.
Expansion fittings on PEX-A keep the inside of each joint wide open, which helps flow. Both are used on repipes.
What's the difference between Type L and Type M copper?
Wall thickness. Type L has a thicker wall than Type M, uses more copper, and costs more. Type M is thinner, lighter, and cheaper. Type K is thicker still and is mostly used for underground water service lines. The type is printed on the pipe in color: blue for Type L and red for Type M.
Which one costs less?
PEX, almost every time. The tubing costs less, and the labor is a lot less because PEX bends instead of needing a fitting at every turn. Fewer fittings also usually means fewer and smaller wall openings, which means less drywall work at the end.
For more on what drives the total, see our Roseville repipe cost guide.
When does copper make more sense?
Most people pick PEX. Copper makes sense when:
- You've had rodents in the attic and don't want plastic up there
- Part of the pipe will be exposed to sunlight or high heat
- You just want metal pipe and don't mind the higher cost
- You want the exposed pipe under sinks and at the water heater to look like copper
Some homeowners split it: PEX inside the walls and copper where it shows. That works too, with the right transition fittings.
Does Roseville's water favor one or the other?
Not in a way that settles it. Roseville blends soft Folsom Lake water with groundwater that's harder and varies a lot. The city's 2025 water quality report lists Folsom Lake water at an average hardness of 26 parts per million and groundwater at an average of 95, with readings from 31 to 280. The report also says pH is adjusted at the treatment plant to reduce corrosion.
Copper can get pinhole leaks over time, and there's no single cause. PEX doesn't corrode the way metal does. But installation matters just as much as material for either one.
Which one do we recommend?
For most Roseville homes, PEX. It costs less, goes in faster, needs fewer wall openings, and does the job. If you have a good reason to want copper, we'll install copper.
See PEX repiping and copper repiping for how each job goes, or our main page on whole house repipes in Roseville.
PEX vs. copper FAQs
Does PEX last as long as copper?
Is PEX safe for drinking water?
Can you mix PEX and copper in one house?
Is PEX-A worth the extra cost?
Will a PEX repipe lower my water pressure?
Why do some plumbers prefer copper?
Related services
Still deciding between PEX and copper?
Call us. We'll price both for your house so you can compare.